DECKEL MAHO DMU 75 monoBlock – Year 2014
CNC 5 Axis Machining Center
| Axis X | 750 mm |
| Axis Y | 650 mm |
| Axis Z | 560 mm |
| CNC | HEIDENHAIN iTNC 530 |
| Max. part weight | 600 kg |
Made in Germany.
Year of Made: 2014.
Manufacturer: DECKEL MAHO.
Machine Status: Very Good General Condition.
Numerical Control: HEIDENHAIN iTNC 530.
X-Axis Travel: 750 mm.
X-Axis Feed Rates: 0 to 40.000 mm/min.
X-Axis Rapid Feed Rates: 40.000 mm/min.
X-Axis Feedd Force: 7 kN.
X-Axis Acceleration: 6m/sec2.
Y-Axis Travel: 650 mm.
Y-Axis Feed Rates: 0 to 40.000 mm/min.
Y-Axis Rapid Feed Rates: 40.000 mm/min.
Y-Axis Feedd Force: 13 kN.
Y-Axis Acceleration: 6m/sec2.
Z-Axis Travel: 560 mm.
Z-Axis Feed Rates: 0 to 40.000 mm/min.
Z-Axis Rapid Feed Rates: 40.000 mm/min.
Z-Axis Feedd Force: 10 kN.
Z-Axis Acceleration: 6m/sec2.
CNC Swivel Rotary Table:
Worktable Diameter(C Axis): 650 mm, integrated in
a rigid Table of 800 X 650 mm.
Max. Workpiece Weight on the Worktable: 600 kg.
MILLING SPINDLE
Max. Powered Spindle Rotation Speed:
18.000 Rpm.
Motorized Spindle Drive Power:
At 40% Duty Cycle: 35 kW.
At 100% Duty Cycle: 25 kW.
Tool Magazine: 60 Positions.
Tool Changer Type: Double Clamp.
Tool Holder: HSK-A 63, according to DIN 69893.
Max. Tool Diameter:
With free neighboring positions: 160 mm.
With occuped neighboring positions: 80 mm.
Max. Tool Length: 315 mm.
Max. Tool Weight: 8.0 kg.
Tool Changing Time(Chip to Chip): 4.9 sec.
Coolant through the Center of the Spindle: 40 bar.
Debit: 23 Liters/min.
Tank Capacity: 600 Liters.
Paper Belt Filter.
Scraper Belt Chip Conveyor, Width 670 mm, unloading
Height 950 mm.
EQUIPMENT
Electronic Handwheel.
Spindle Cooling Nozzles: 15 Water Jets, 5 Air Jets.
Chips Flushing in the Working Area.
Rinsing Gun with Pump: 1 bar, 40 Liters/min.
Oil and Emulsion Mist Separation System, mechanical filter:
Flow Volume: 600 m3/Hour.
MPC Machine Protection Control.
HEIDENHAIN TS 649 Infrared Probe.
BLUM Tool Calibration System.
3D Quick Set.
Toolbox to check and correct the Kinematic Accuracy
of the Machine Configuration in 4/5 Axis.
Rotating Viewing Window.
Machine Hours under Power: 52.5275.
Spindle Working Hours: 19.993.
Total Power Requirement: 48 kVA.
Machine Weight: ̃ 11.600 kg.
Machine Dimensions: ̃ 5.000 X 3.000 X 3.000 mm.
The Milling Spindle of the machine was changed three years ago.
The machine comes with HSK-A 63 Tool Holders
(about 60-80 Pieces). Most of them are HAIMER
Shrink-Fit Tool Holders or ER32 Collets.
