AMADA CMB 150 CNC fully automatic circular carbide saw – Year 2012
| AMADA CMB 150 – Technical Specifications | |
|---|---|
| GENERAL INFORMATION | |
| Brand | AMADA |
| Model | CMB 150 |
| Year | 2012 |
| CUTTING CAPACITY | |
| Round Capacity | 75 mm – 152 mm (2.95″ – 6″) |
| Rectangle Capacity | 75 x 75 mm – 100 x 100 mm (2.95″ x 2.95″ – 3.94″ x 3.94″) |
| BLADE & SPINDLE | |
| Blade Diameter | 457 mm (18″) |
| Blade Dimensions | 460 mm x 50 mm x 2.8 mm (18.1″ x 1.97″ x 0.11″) |
| Blade Speed | 39 – 149 RPM (inverter driven) |
| MOTOR & POWER | |
| Main Blade Motor | 11 kW (15 HP) |
| Feed Motor | 2.05 kW (2.75 HP) |
| Hydraulic Pump Motor | 1.5 kW (2 HP) |
| Cut-to-Length Feed Motor | 0.56 kW (0.75 HP) |
| MATERIAL HANDLING | |
| Max Stock Table Capacity | 6000 mm x 152 mm x 3 bars (19’7″ x 6″ x 3 bars) / 2,600 kg (5,732 lbs) |
| Incline Table Dimensions | 5380 mm x 1191 mm x 1118 mm (17’8″ x 46.9″ x 44″) |
| Material Index Stroke | 755 mm (29.7″) |
| Material Index Length | 45 mm – 12,000 mm (1.78″ – 472.44″) |
| End Trim Length | 20 mm – 40 mm (0.78″ – 1.57″) |
| Remnant Length | 45 mm (1.77″) |
| COOLANT & HYDRAULICS | |
| Hydraulic Tank Capacity | 20 L (5.3 gallons) |
| Coolant System | Mist Coolant |
| CONTROL SYSTEM | |
| Control Type | Mitsubishi PLC |
| DIMENSIONS & WEIGHT | |
| Machine Dimensions (L x W x H) | 2162 x 1966 x 1882 mm (85.1″ x 77.4″ x 74.1″) |
| Table Height | 800 mm (31.5″) |
| Machine Weight | 3,000 kg (6,613 lbs) |
| EQUIPPED WITH | |
| Mist coolant, chip conveyor, Mitsubishi PLC control, automatic sorting system, automatic trim cut, anti-backlash device, cut piece counter, carbide stabilizer pads, amp meter, Dyna guide linear blade guide system, wire chip brush |
|
| Used Bandsaw – 20 Point Inspection and Repair Process | |
|---|---|
| # | Description |
| 1 | Gear Reducer – Inspect for bearing or gear wear, shaft play, gear lash, seal leakage, or noise. Replace parts as necessary. |
| 2 | Vari-Drive – Check pulley wear, alignment, belt condition, and speed changer operation. Recalibrate blade speed indicator. |
| 3 | Hydraulic System – Check leaks; inspect valves, cylinders, gauges, and fittings. Replace parts if required. |
| 4 | Cam Followers – Inspect and lubricate (dual column machines). |
| 5 | Blade Tension Assembly – Lubricate slider plate and adjust tension. |
| 6 | Hydraulic Oil and Filter – Inspect and replace if necessary. |
| 7 | Lubrication Points – Grease or oil bearings, pivot points, guide rails, screws, pillow blocks, and chains. |
| 8 | System & Cutting Pressures – Check and adjust. |
| 9 | Powered Blade Brush – Check operation and replace if needed. |
| 10 | Vises & Barfeed – Inspect vise wear, alignment, and feed operation. |
| 11 | Blade Guides – Inspect condition and replace if necessary. |
| 12 | Band Wheels – Inspect wear, taper, bearings, and runout. Replace as required. |
| 13 | Guide Arm Assembly – Check alignment and ensure blade is square to vise. |
| 14 | Blade Tracking – Inspect and adjust if needed. |
| 15 | Feed System – Calibrate feed rate. |
| 16 | Coolant System – Check pump and coolant lines condition. |
| 17 | Electrical – Inspect wiring, connections, and insulation condition. |
| 18 | Control Switches – Check operation and replace if necessary. |
| 19 | Limit Switches – Check adjustment and operation. |
| 20 | Final Run Off – Test machine, perform cutting test, and verify accuracy and squareness. |
